Our Products

IKRON - HF 410 SERIES SUCTION FILTERS

The following factors should be analysed when choosing the ideal filter:

  • The filtration degree required to protect the most sensitive component from contamination.
  • The points of the circuit in which the filters have to be installed.
  • The working pressure of the system.
  • The maximum flow rate and the type of fluid to be filtered.
  • The duty cycle.
  • The retention efficiency of the filtering cartridge.
  • The contaminant accumulation capacity of the filtering cartridge.
  • The working ambient temperature.

The HF 410 and HF 412 suction line filters series are directly connected to the circuit's suction line and protect the system's components against contaminant particles.
The filters can be supplied with by-pass valve set at 2.9 psi (0,2 bar).
In the 10-20-30 dimensions, the HF 412 serie is made with an outside diameter smaller than the relative HF 410 versions.

  • Flow up to 80 US gpm (300 l/min).
  • By-pass valve
  • "FS" version with oversized filtering surface

Each filter used generates a pressure drop that increases continuously as time goes by.
This pressure drop represents an efficiency index of the filter itself. When the hydraulic system is about to be assembled, all the components must be perfectly clean and the fluid has to be added through a device complete with a filter. During the test phase, it is advisable to run some work cycles at low pressure in order to create the best possible conditions for all the components.

IKRON - HF 410 SERIES SUCTION FILTERS
CİNSİ Debi Filtrasyon Diş
HF410 (lt/dak.) Mikron(µm) Ölçüsü
HF 410-10-060-MI 125 20 125 1/2"
HF 410-20-077-MI 125 30 125 3/4"
HF 410-20-122-MI 125 40 125 3/4"
HF 410-30-122-MI 125 60 125 1"
HF 410-30-122-MI 125 90 125 1 1/2"
HF 410-30-162-MI 125 120 125 1 1/2"
HF 410-30-195-MI 125 130 125 1 1/2"
HF 412-30-241-MI 125 200 125 2"
HF 410-40-122-MI 125 130 125 2"
HF 410-40-162-MI 125 140 125 2"
HF 410-40-195-MI 125 220 125 2 1/2
HF 410-40-239-MI 125 300 125 3"
IKRON - HF 410/412 MAGNETIC SUCTION FILTERS
CİNSİ Debi Filtrasyon Diş
HF410 (lt/dak.) Mikron(µm) Ölçüsü
HF 412-30-241 200 125 2"
HF 410-40-122 130 125 2"
IKRON - HF 595 LINE TYPE SUCTION and RETURN FILTERS
CİNSİ Debi Filtrasyon Diş
HF 595 (lt/dak.) Mikron(µm) Ölçüsü
HF 595-10.060 SP025 Dönüş 25 25 1/2"
HF 595-10.060 MB125 Emiş 30 125 1/2"
HF 595-20.077 SP025 Dönüş 60 25 3/4"
HF 595-20.077 MB125 Emiş 70 125 3/4"
HF 595-20.122 SP025 Dönüş 120 25 1"
HF 595-20.122 MB125 Emiş 120 125 1"
HF 595-30.195 SP025 Dönüş 190 25 1 1/4"
HF 595-30.195 MB125 Emiş 180 125 1 1/4"
IKRON - HF 620 IN LINE SUCTION and RETURN FILTERS
CİNSİ Emiş (lpm) Emiş (lpm) Dönüş (lpm) Dönüş (lpm) Maks. Basınç Diş
HF620 10 µm 25 µm 10 µm 25 µm (bar) Ölçüsü
           
HF 620-20.135-SP 30 35 65 75 12 3/4"
HF 620-20.180-SP 35 40 75 80 12 3/4"
HF 620-30.155-SP 75 90 165 195 12 11/4"
HF 620-30.210-SP 80 100 180 200 12 11/4"
HF 620-30.305 SP 100 105 200 210 12 11/4"
HF 620-40.155-SP 100 140 230 300 12 11/2"
HF 620-40.210-SP 130 150 270 310 12 11/2"
HF 620-40.305-SP 150 160 310 340 12 11/2"
HF 620-50.155-SP 100 140 230 300 12 11/2"
HF 620-50.210-SP 130 150 270 310 12 11/2"
HF 620-50.305-SP 150 160 310 340 12 11/2"
IKRON - HF 525 IN LINE SUCTION and RETURN FILTERS (HYDROSTATIC APPLICATIONS)
CİNSİ Debi (lt/dak.) Debi (lt/dak.) Filtrasyon Maks. Basınç Diş
HF525 Emiş Dönüş Mikron (µm) (bar) Ölçüsü
         
HF525-20.242-AS-FG 40 80 10 10 3/4" + 1"
HF525-30.292-AS-FG 125 250 10 10 1 1/4" (2 ad) + 1" (2 ad)